Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Expand
A Complete TXT Configuration Example
A Complete TXT Configuration Example
Code Block
borderStylesolid
titleA Complete TXT Configuration Example
<<VOIP CONFIG FILE>>Version:2.0002

<GLOBAL CONFIG MODULE>
WAN Mode           :DHCP
WAN IP             :10.27.74.109
WAN Subnet Mask    :255.255.255.0
WAN Gateway        :10.27.74.254
Primary DNS        :10.27.74.1
Secondary DNS      :0.0.0.0
Enable DHCP        :1
Use Vendor Class ID:0
Vendor Class ID    :Asterisk
DHCP Auto DNS      :1
DHCP Auto Time     :1
DHCP Option 100-101:1
ARP Cache Life     :10
Enable PPPoE       :0
RTP Initial Port   :10000
RTP Port Quantity  :200
SNTP Server        :0.digium.pool.ntp.org
Second SNTP Server :1.digium.pool.ntp.org
Enable SNTP        :1
Time Zone          :-32
Location           :3
Time Zone Name     :UTC-8
Enable DST         :1
DST Fixed Type     :2
SNTP Timeout       :5000
DST Min Offset     :60
DST Start Mon      :3
DST Start Week     :5
DST Start Wday     :0
DST Start Hour     :2
DST End Mon        :10
DST End Week       :5
DST End Wday       :0
DST End Hour       :2
Language           :0
Push XML IP        :
Enable Call History:1
Active Uri IP      :
Boot Completed Url :
Reg On Url         :
Reg Off Url        :
Reg Failed Url     :
Offhook Url        :
Onhook Uri         :
Incmoing Call Url  :
Outgoing Call Url  :
Call Active Url    :
Call Stop Url      :
DND On Url         :
DND Off Url        :
Always FWD On Url  :
Always FWD Off Url :
Busy FWD On Url    :
Busy FWD Off Url   :
No Ans FWD On Url  :
No Ans FWD Off Url :
Transfer Url       :
B Transfer Url     :
A Transfer Url     :
Hold Url           :
Unhold Url         :
Mute Url           :
Unmute Url         :
Missed call Url    :
IP Change Url      :
Idle to Busy Url   :
Busy to Idle Url   :
ATE ID             :
All Pswd Encryption:0

<TELE CONFIG MODULE>
Dial by Pound      :1
BTransfer by Pound :1
Onhook to BXfer    :0
Onhook to AXfer    :1
Memory Key to BXfer:0
Xfer On Conf Onhook:0
Dial Fixed Length  :0
Fixed Length Nums  :11
Dial by Timeout    :1
Dial Timeout value :5
Dialpeer With Line :0
Accept Any Call    :1
IP Dial Prefix     :.
Auto Switch Call   :0
--Port Config--    :
P1 Enable DND      :0
P1 DND Mode        :0
P1 Call Record Type:0
P1 Enable Force Rin:0
P1 Mute Ringing    :0
P1 CWaiting Tone   :1
P1 Ban Dial Out    :0
P1 Ban Empty CID   :0
P1 Enable CLIP     :1
P1 CallWaiting     :1
P1 CallTransfer    :1
P1 CallSemiXfer    :1
P1 CallConference  :1
P1 AutoAnswer      :0
P1 No Answer Time  :20
P1 Warm Line Time  :0
P1 Hotline Num     :
P1 Auto PickupNext :0
P1 Busy No Line    :0
P1 Auto Onhook     :1
P1 Auto Onhook Time:3
P1 DND Code        :1
P1 Busy Code       :2
P1 Reject Code     :3
P1 Caller Name Type:0
P1 Enable Intercom :1
P1 Intercom Mute   :0
P1 Intercom Tone   :1
P1 Intercom Barge  :1
P1 Use Auto Redial :0
P1 AutoRedial Delay:10
P1 AutoRedial Times:10
P1 Call Complete   :0
P1 Hide DTMF Type  :0
P1 Talk DTMF Tone  :1
P1 Dial DTMF Tone  :1
P1 Psw Dial Mode   :0
P1 Psw Dial Length :0
P1 Psw Dial Prefix :
P1 Enable MultiLine:1
P1 Allow IP Call   :1
P1 CHolding Tone   :1
P1 Number Privacy  :0
P1 Privacy Rule    :
Transf SDial       :0
Enable Code Plan   :0
Country Code       :
Area Code          :
Transf DTMF Code   :
Hold DTMF Code     :
Conf DTMF Code     :
Conf Limit Rule    :
End Two Ext Conf   :0
--Code Plan List-- :
P1 rule            :

<DSP CONFIG MODULE>
Signal Standard    :11
Enable MWI Tone    :1
Play Egress DTMF   :2
Onhook Time        :120
G729 Payload Len   :1
G723 Bit Rate      :1
G722 Timestamps    :0
VAD                :1
Ring Type          :2
Dtmf Payload Type  :101
TX AGC             :0
RX AGC             :0
Headset MIC offset :3
Headset spkr offset:7
Sidetone GAIN      :1
EHS Type           :0
RTP Keep Alive     :0
Session Report     :0
Interval Report    :0
Interval Period    :60
MOS-LQ Warning     :40
MOS-LQ Critical    :25
Delay Warning      :150
Delay Critical     :200
Phone Report       :0
WEB Report         :0
--Port Config--    :
P1 General Spk Vol :5
P1 General Mic Vol :3
P1 Headset Vol     :5
P1 Ring in Headset :0
P1 Auto Headset    :0
P1 Headset Ring Vol:5
P1 HandFree Vol    :5
P1 RingTone Vol    :5
P1 Voice Codec1    :G722/8000
P1 Voice Codec2    :PCMA/8000
P1 Voice Codec3    :PCMU/8000
P1 Voice Codec4    :G729/8000
P1 Voice Codec5    :
P1 Voice Codec6    :
--Alert Info Ring--:
Alert1 Text        :
Alert1 Ring Type   :1
 
<SIP CONFIG MODULE>
SIP  Port          :5060
STUN Server        :
STUN Port          :3478
STUN Refresh Time  :50
SIP Wait Stun Time :800
Extern NAT Addrs   :
Reg Fail Interval  :32
SIP Pswd Encryption:0
Strict BranchPrefix:0
Enable Group Backup:0
Enable RFC4475     :1
SIP invite strict  :1
Notify Reboot      :0
SMS direct Enabled :0
SMS Save Enabled   :1
SMS Ring Enabled   :1
CSTA Enable        :0
Strict UA Match    :0
--SIP Line List--  :
SIP1 Phone Number  :
SIP1 Display Name  :
SIP1 Sip Name      :
SIP1 Register Addr :
SIP1 Register Port :5060
SIP1 Register User :
SIP1 Register Pswd :
SIP1 Register TTL  :3600
SIP1 Enable Reg    :0
SIP1 Proxy Addr    :
SIP1 Proxy Port    :5060
SIP1 Proxy User    :
SIP1 Proxy Pswd    :
SIP1 BakProxy Addr :
SIP1 BakProxy Port :5060
SIP1 Enable Failbac:0
SIP1 Signal Crypto :0
SIP1 SigCrypto Key :
SIP1 Media Crypto  :0
SIP1 MedCrypto Key :
SIP1 SRTP Auth-Tag :0
SIP1 Local Domain  :
SIP1 Always FWD    :0
SIP1 Busy FWD      :0
SIP1 No Answer FWD :0
SIP1 Always FWD Num:
SIP1 Busy FWD Num  :
SIP1 NoAnswer FWD N:
SIP1 FWD Timer     :5
SIP1 Ring Type     :0
SIP1 Hotline Num   :
SIP1 Enable Hotline:0
SIP1 WarmLine Time :0
SIP1 Pickup Num    :
SIP1 Join Num      :
SIP1 NAT UDPUpdate :2
SIP1 UDPUpdate TTL :30
SIP1 Server Type   :0
SIP1 User Agent    :
SIP1 PRACK         :1
SIP1 Keep AUTH     :0
SIP1 Session Timer :0
SIP1 S.Timer Expire:0
SIP1 Enable GRUU   :0
SIP1 DTMF Mode     :3
SIP1 DTMF Info Mode:0
SIP1 NAT Type      :0
SIP1 Enable Rport  :1
SIP1 Subscribe     :0
SIP1 Sub Expire    :3600
SIP1 Single Codec  :0
SIP1 CLIR          :0
SIP1 Strict Proxy  :0
SIP1 Direct Contact:0
SIP1 History Info  :0
SIP1 DNS SRV       :0
SIP1 DNS Mode      :0
SIP1 XFER Expire   :0
SIP1 Ban Anonymous :0
SIP1 Dial Off Line :0
SIP1 Quota Name    :0
SIP1 Presence Mode :0
SIP1 RFC Ver       :1
SIP1 Signal Port   :5060
SIP1 Transport     :0
SIP1 Enable ChgPort:1
SIP1 TLS Version   :0
SIP1 Use SRV Mixer :0
SIP1 SRV Mixer Uri :
SIP1 Long Contact  :0
SIP1 Auto TCP      :0
SIP1 Uri Escaped   :1
SIP1 Click to Talk :0
SIP1 MWI Num       :
SIP1 CallPark Num  :
SIP1 Retrieve Num  :
SIP1 MSRPHelp Num  :
SIP1 User Is Phone :1
SIP1 Auto Answer   :0
SIP1 NoAnswerTime  :5
SIP1 MissedCallLog :1
SIP1 SvcCode Mode  :0
SIP1 DNDOn SvcCode :
SIP1 DNDOff SvcCode:
SIP1 CFUOn SvcCode :
SIP1 CFUOff SvcCode:
SIP1 CFBOn SvcCode :
SIP1 CFBOff SvcCode:
SIP1 CFNOn SvcCode :
SIP1 CFNOff SvcCode:
SIP1 ANCOn SvcCode :
SIP1 ANCOff SvcCode:
SIP1 Send ANOn Code:
SIP1 Send ANOffCode:
SIP1 CW On Code    :
SIP1 CW Off Code   :
SIP1 VoiceCodecMap :G722,G711U,G711A,G729,G726-32,G723
SIP1 BLFList Uri   :
SIP1 BLF Server    :
SIP1 Respond 182   :0
SIP1 Enable BLFList:0
SIP1 Caller Id Type:4
SIP1 Syn Clock Time:0
SIP1 Use VPN       :1
SIP1 Enable DND    :0
SIP1 Update Reg Exp:1
SIP1 Inactive Hold :0
SIP1 Enable SCA    :0
SIP1 Sub CallPark  :0
SIP1 Hoteling Event:0
SIP1 Sub CC Status :0
SIP1 CSTA Number   :
SIP1 Feature Sync  :0
SIP1 Req With Port :1
SIP1 Enable Mute   :0
SIP1 VQ Name       :
SIP1 VQ Server     :
SIP1 VQ Server Port:5060
SIP1 VQ HTTP Server:
SIP1 Unreg Reboot  :0
SIP1 Flash Mode    :0
SIP1 Use Tel Call  :0
SIP1 Content Type  :
SIP1 Content Body  :
SIP1 Deal 180      :1
SIP1 Ena MAC Header:0
SIP1 Ena REG MAC   :0
SIP1 BLF dialog mat:1

<MCAST CFG MODULE>
Priority           :0
Enbale Priority    :0
--Mcast Addr--     :
MCAST1 Port        :0
MCAST1 Name        :
MCAST1 Host        :
 
<PPPoE CONFIG MODULE>
PPPoE User         :user123
PPPoE Password     :password
PPPoE Svc Name     :ANY
PPPoE IP Address   :

<MMI CONFIG MODULE>
Web Port           :80
Web Server Type    :0
Https Web Port     :443
Enable MMI Filter  :0
Web Authentication :0
Default WEB User   :0
--MMI Account--    :
Account1 Name      :admin
Account1 Password  :789
Account1 Level     :10

<QOS CONFIG MODULE>
Enable VLAN        :0
Enable diffServ    :1
LLDP Transmit      :1
LLDP Refresh Time  :60
LLDP Learn Policy  :1
CDP Enabled        :0
CDP Refresh Time   :60
Singalling DSCP    :-1
Voice DSCP         :46
VLAN ID            :256
Signalling Priority:0
Voice Priority     :0
LAN Port Priority  :0
VLAN Recv Check    :1
Enable PVID        :1
PVID Value         :254
DHCP Option Vlan   :0

<DEBUG CONFIG MODULE>
MGR Trace Level    :0
SIP Trace Level    :0
Trace File Info    :0
Enable Watch Dog   :1
Enable Memory Info :0

<AAA CONFIG MODULE>
Enable Syslog      :0
Syslog address     :0.0.0.0
Syslog port        :514

<ACCESS CONFIG MODULE>
Enable In Access   :0
Enable Out Access  :0

<PHONE CONFIG MODULE>
Menu Password      :789
KeyLock Password   :123
Fast Keylock Code  :
Enable KeyLock     :0
KeyLock Status     :0
Emergency Call     :110
LCD Title          :Asterisk
LCD Constrast      :5
LCD Luminance      :1
Backlight Off Time :30
ScrnSaver Wait Time:0
KeyLock Timeout    :0
Enable Power Led   :0
SMS MWI Power Led  :0
Miss Call Power Led:0
Talk Dial Power Led:0
Ringing Power Led  :0
Mute Call Power Led:0
Hold Power Led     :0
Time Display Style :0
Phone Model        :A25
FuncKey Page Num   :2
Blf Default type   :0
Alarm  Clock       :0,,1
Disable CHN IME    :0
Disable Dial Search:0
Redial Enter CLog  :1
Date Display Style :0
Date Separator     :0
Enable Pre-Dial    :1
Default Line       :0
Enable Default Line:0
Enable Auto SelLine:1
Agent Username     :
Agent Password     :
Agent Number       :
Agent Sipline      :0
Agent Status       :0
Agent Status Reason:
--BW Calllogs Conf-:
BWCLog1 Title      :
BWCLog1 URL        :
BWCLog1 Username   :
BWCLog1 Password   :
BWCLog1 SipLine    :0
--BW Directory Conf:
BWDir1 Title       :
BWDir1 URL         :
BWDir1 Username    :
BWDir1 Password    :
BWDir1 SipLine     :0
--LDAP Config--    :
LDAP1 Title        :
LDAP1 Server       :
LDAP1 port         :389
LDAP1 Authenticate :0
LDAP1 Version      :3
LDAP1 Calling Line :0
LDAP1 Enable Search:0
LDAP1 Bind Line    :0
LDAP1 Base         :
LDAP1 Username     :
LDAP1 Password     :
LDAP1 Tel Attr     :telephoneNumber
LDAP1 Mobile Attr  :mobile
LDAP1 Other Attr   :home
LDAP1 Displayname  :cn
LDAP1 Filter Name  :
LDAP1 Filter number:
--Xml PhoneBook--  :
XML-PBook1 Name    :
XML-PBook1 Addr    :
XML-PBook1 Auth    :
XML-PBook1 Policy  :0
XML-PBook1 Sipline :0
XML-PBook1 BindLine:0
Phonebook Groups   :
--Function Key--   :
Fkey1 Type         :2
Fkey1 Value        :SIP1
Fkey1 Title        :
--Soft Dss Key--   :
SoftFkey1 Type     :0
SoftFkey1 Value    :
SoftFkey1 Title    :
Ui font Color      :0xFFFFFF$0x444343
Ui Title Color     :0x000026$0x4f79a7
Ui Softkey Color   :up:0x5e6f85$0x485972@ down:0x00$0xffc83b
Ui List  Color     :0x00$0xa9c1c9
Ui Balloon Color   :0x00$0x6c7b8d
Ui Second Color    :odd:0xc9d9eb$0x9fc0e3@ even:0x356291$0x7296bb@ select:0x34373c$0xe2a917@ interval:0x4478ae@ LSKbgc:0x6b84aa
Ui ScrnSaver Color :0x00$0x808080
Vqm Display Order  :
DSS Home Page      :0
Download Pb search :0

<SCREEN KEY CONFIG MODULE>
Desktop Softkey    :history;contact;dnd;menu;
Talking Softkey    :hold;xfer;conf;end;
Ringing Softkey    :accept;none;cfwd;reject;
Alerting Softkey   :none;none;none;end;
XAlerting Softkey  :xfer;none;none;end;
Conference Softkey :hold;none;split;end;
Waiting Softkey    :hold;xfer;conf;end;
Ending Softkey     :repeat;none;none;end;
DialerPre Softkey  :delete;save;send;exit;
DialerCall Softkey :delete;history;send;exit;
DialerXfer Softkey :delete;xfer;send;exit;
DialerCfwd Softkey :delete;none;cfwd;exit;
Desktop Click      :history;status;paccout;naccout;menu;
Dailer  Click      :pline;nline;none;none;none;
Call    Click      :pcall;ncall;voldown;volup;none;
Desktop Long Press :status;none;none;sdial;reset;
Softkey Mode       :1
Softkey Exit Style :1

<RECORD CONFIG MODULE>
Enabled            :0
Voice Codec        :PCMA
Enable Server Rec  :0
Enable PBX Rec     :0
Server Addr        :
Server Port        :0
Type               :0

<AUTOUPDATE CONFIG MODULE>
Download Username  :
Download Password  :
AP Pswd Encryption :0
FDPS Enable        :1
Config File Name   :
Config File Key    :
Common Cfg File Key:
Download Server IP :
Download Protocol  :0
Download Mode      :0
Download Interval  :1
DHCP Option        :66
Save DHCP Opion    :0
DHCP Option 120    :0
PNP Enable         :1
PNP IP             :224.0.1.75
PNP Port           :5060
PNP Transport      :0
PNP Interval       :1
Save Provision Info:0
Download CommonConf:1
Download DeviceConf:1
Check FailTimes    :5
update PB Interval :720
Clr PB B4 Import   :0
Trust Certification:0
Device Cert Mode   :1
Auto SErver Digest :0
Enable Auto Upgrade:0
Upgrade Server 1   :
Upgrade Server 2   :
Auto Upgrade intval:24

<VPN CONFIG MODULE>
VPN mode           :2
L2TP LNS IP        :
L2TP User Name     :
L2TP Password      :
L2TP Negotiate DNS :1
Enable VPN Tunnel  :0
VPN Server IP      :0.0.0.0
VPN Server Port    :80
Server Group ID    :VPN
Server Area Code   :12345

<DOT1X CONFIG MODULE>
Xsup User          :admin
Xsup Password      :admin
Xsup Enable        :0
Xsup AuthMac       :01:80:C2:00:00:03
Xsup UseDefaultMac :1

<TR069 CONFIG MODULE>
ACS Server Type    :1
ACS URL            :0.0.0.0
ACS UserName       :admin
ACS Password       :admin
CPE UserName       :dps
CPE Password       :dps
CPE SerialNumber   :
ProvisioningCode   :
Download Start Time:0
Download End Time  :0
TR069 Auto Login   :0
TR069 Tone         :1
Enable TR069       :0
Periodix Interval  :3600
Area Code          :020
TLS Version        :0
<<END OF FILE>> 

...

Expand
Code Block
borderStylesolid
titleTXT TELE CONFIG MODULE Elements
<<VOIP CONFIG FILE>>
 
<TELE CONFIG MODULE>
Dial by Pound      :1
BTransfer by Pound :1
Onhook to BXfer    :0
Onhook to AXfer    :1
Memory Key to BXfer:0
Xfer On Conf Onhook:0
Dial Fixed Length  :0
Fixed Length Nums  :11
Dial by Timeout    :1
Dial Timeout value :5
Dialpeer With Line :0
Accept Any Call    :1
IP Dial Prefix     :.
Auto Switch Call   :0
--Port Config--    :
P1 Enable DND      :0
P1 DND Mode        :0
P1 Call Record Type:0
P1 Enable Force Rin:0
P1 Mute Ringing    :0
P1 CWaiting Tone   :1
P1 Ban Dial Out    :0
P1 Ban Empty CID   :0
P1 Enable CLIP     :1
P1 CallWaiting     :1
P1 CallTransfer    :1
P1 CallSemiXfer    :1
P1 CallConference  :1
P1 AutoAnswer      :0
P1 No Answer Time  :20
P1 Warm Line Time  :0
P1 Hotline Num     :
P1 Auto PickupNext :0
P1 Busy No Line    :0
P1 Auto Onhook     :1
P1 Auto Onhook Time:3
P1 DND Code        :1
P1 Busy Code       :2
P1 Reject Code     :3
P1 Caller Name Type:0
P1 Enable Intercom :1
P1 Intercom Mute   :0
P1 Intercom Tone   :1
P1 Intercom Barge  :1
P1 Use Auto Redial :0
P1 AutoRedial Delay:10
P1 AutoRedial Times:10
P1 Call Complete   :0
P1 Hide DTMF Type  :0
P1 Talk DTMF Tone  :1
P1 Dial DTMF Tone  :1
P1 Psw Dial Mode   :0
P1 Psw Dial Length :0
P1 Psw Dial Prefix :
P1 Enable MultiLine:1
P1 Allow IP Call   :1
P1 CHolding Tone   :1
P1 Number Privacy  :0
P1 Privacy Rule    :
Transf SDial       :0
Enable Code Plan   :0
Country Code       :
Area Code          :
Transf DTMF Code   :
Hold DTMF Code     :
Conf DTMF Code     :
Conf Limit Rule    :
End Two Ext Conf   :0
--Code Plan List-- :
P1 rule            :
<<END OF FILE>>

...

Option

Values

Description

Dial by Pound

Boolean, Defaults to 1

If disabled, the phone will not allow the use of the # key to send a call upon completion of dialing. The sent number does not include the # DTMF. Defaults to 1.

BTransfer by PoundBoolean, Defaults to 1If enabled, the phone will allow the use of the # key to blind transfer a call. Defaults to 1.
Onhook to BXferBoolean, Defaults to 0If enabled, the phone will allow the completion of a blind transfer by a cradling of the handset. Defaults to 0.
Onhook to AXferBoolean, Defaults to 1If enabled, the phone will allow the completion of an attended transfer by a cradling of the handset. Defaults to 1.
Memory Key to BXferBoolean, Defaults to 0If enabled, pressing a BLF after using the transfer hard key will affect a blind transfer. Defaults to 0.
Xfer On Conf OnhookBoolean, Defaults to 0If enabled, going on-hook can complete a conference transfer. Defaults to 0.
Dial Fixed LengthBoolean, Defaults to 0If enabled, the phone will immediately dial the number that has been input according to a match of Fixed Length Nums. Defaults to 0.
Fixed Length NumsInteger, Defaults to 11Sets a number of digits that once entered, if Dial Fixed Length is enabled, will be immediately dialed. Defaults to 11.
Dial by TimeoutBoolean, Defaults to 1If disabled, the phone will not initiate a dial once the timeout set by Dial Timeout value is reached. Defaults to 1.
Dial Timeout valueInteger, in seconds, Defaults to 5Sets the amount of time, in seconds, the phone will wait for additional digits before completing a dial. Defaults to 5
Dialpeer With Line0Defaults to 0.
Accept Any CallBoolean, Defaults to 1If disabled, the phone will not allow anonymous incoming calls. Defaults to 1.
IP Dial PrefixString, Defaults to .Sets a dialing prefix to be prepended before making IP dialed calls. Defaults to .
Auto Switch CallBoolean, Defaults to 0If enabled, the phone will switch and provide ringing indication for new incoming calls if a multicast call was already in progress. Defaults to 0.
Transf SDialDTMFIf defined, and if you have a speed dial set for this digit, the phone will, in the transfer state, use the speed dial assigned for this digit to affect the transfer.
Enable Code PlanBoolean, Defaults to 0If enabled, the phone will automatically truncate incoming numbers using the country code as defined by Country Code, Area Code and Code Plan List. Defaults to 0.
Country CodeStringSets the country code to be truncated from incoming numbers.
Area CodeStringSets the area code to be truncated from incoming numbers.
Transfer DTMF CodeDTMF stringIf defined, sets digits that are sent to the server when a transfer is executed, in order to affect server-side transfer logic.
Hold DTMF CodeDTMF stringIf defined, sets digits that are sent to the server when a hold is executed, in order to affect server-side hold logic.
Conf DTMF CodeDTMF stringIf defined, sets digits that are sent to the server when a conference is executed, in order to affect server-side conference logic.
Conf Limit RuleInteger, Max 30, Defaults to NullFor server-side conferences, defines the maximum number of digits for a party that is to be added to the conference. If set to 0, then numbers starting with 0 cannot be added into a conference.
End Two Ext ConfBoolean, Defaults to 0If enabled, Conf Limit Rules are applied for both parties in a joined conference.
Port Config and Port Config Entry Element

...

Expand
Code Block
borderStylesolid
titleTXT SIP CONFIG MODULE Elements
<<VOIP CONFIG FILE>>
 
<SIP CONFIG MODULE>
SIP  Port          :5060
STUN Server        :
STUN Port          :3478
STUN Refresh Time  :50
SIP Wait Stun Time :800
Extern NAT Addrs   :
Reg Fail Interval  :32
SIP Pswd Encryption:0
Strict BranchPrefix:0
Enable Group Backup:0
Enable RFC4475     :1
SIP invite strict  :1
Notify Reboot      :0
SMS direct Enabled :0
SMS Save Enabled   :1
SMS Ring Enabled   :1
CSTA Enable        :0
Strict UA Match    :0
--SIP Line List--  :
SIP1 Phone Number  :
SIP1 Display Name  :
SIP1 Sip Name      :
SIP1 Register Addr :
SIP1 Register Port :5060
SIP1 Register User :
SIP1 Register Pswd :
SIP1 Register TTL  :3600
SIP1 Enable Reg    :0
SIP1 Proxy Addr    :
SIP1 Proxy Port    :5060
SIP1 Proxy User    :
SIP1 Proxy Pswd    :
SIP1 BakProxy Addr :
SIP1 BakProxy Port :5060
SIP1 Enable Failbac:0
SIP1 Signal Crypto :0
SIP1 SigCrypto Key :
SIP1 Media Crypto  :0
SIP1 MedCrypto Key :
SIP1 SRTP Auth-Tag :0
SIP1 Local Domain  :
SIP1 Always FWD    :0
SIP1 Busy FWD      :0
SIP1 No Answer FWD :0
SIP1 Always FWD Num:
SIP1 Busy FWD Num  :
SIP1 NoAnswer FWD N:
SIP1 FWD Timer     :5
SIP1 Ring Type     :0
SIP1 Hotline Num   :
SIP1 Enable Hotline:0
SIP1 WarmLine Time :0
SIP1 Pickup Num    :
SIP1 Join Num      :
SIP1 NAT UDPUpdate :2
SIP1 UDPUpdate TTL :30
SIP1 Server Type   :0
SIP1 User Agent    :
SIP1 PRACK         :1
SIP1 Keep AUTH     :0
SIP1 Session Timer :0
SIP1 S.Timer Expire:0
SIP1 Enable GRUU   :0
SIP1 DTMF Mode     :3
SIP1 DTMF Info Mode:0
SIP1 NAT Type      :0
SIP1 Enable Rport  :1
SIP1 Subscribe     :0
SIP1 Sub Expire    :3600
SIP1 Single Codec  :0
SIP1 CLIR          :0
SIP1 Strict Proxy  :0
SIP1 Direct Contact:0
SIP1 History Info  :0
SIP1 DNS SRV       :0
SIP1 DNS Mode      :0
SIP1 XFER Expire   :0
SIP1 Ban Anonymous :0
SIP1 Dial Off Line :0
SIP1 Quota Name    :0
SIP1 Presence Mode :0
SIP1 RFC Ver       :1
SIP1 Signal Port   :5060
SIP1 Transport     :0
SIP1 Enable ChgPort:1
SIP1 TLS Version   :0
SIP1 Use SRV Mixer :0
SIP1 SRV Mixer Uri :
SIP1 Long Contact  :0
SIP1 Auto TCP      :0
SIP1 Uri Escaped   :1
SIP1 Click to Talk :0
SIP1 MWI Num       :
SIP1 CallPark Num  :
SIP1 Retrieve Num  :
SIP1 MSRPHelp Num  :
SIP1 User Is Phone :1
SIP1 Auto Answer   :0
SIP1 NoAnswerTime  :5
SIP1 MissedCallLog :1
SIP1 SvcCode Mode  :0
SIP1 DNDOn SvcCode :
SIP1 DNDOff SvcCode:
SIP1 CFUOn SvcCode :
SIP1 CFUOff SvcCode:
SIP1 CFBOn SvcCode :
SIP1 CFBOff SvcCode:
SIP1 CFNOn SvcCode :
SIP1 CFNOff SvcCode:
SIP1 ANCOn SvcCode :
SIP1 ANCOff SvcCode:
SIP1 Send ANOn Code:
SIP1 Send ANOffCode:
SIP1 CW On Code    :
SIP1 CW Off Code   :
SIP1 VoiceCodecMap :G722,G711U,G711A,G729,G726-32,G723
SIP1 BLFList Uri   :
SIP1 BLF Server    :
SIP1 Respond 182   :0
SIP1 Enable BLFList:0
SIP1 Caller Id Type:4
SIP1 Syn Clock Time:0
SIP1 Use VPN       :1
SIP1 Enable DND    :0
SIP1 Update Reg Exp:1
SIP1 Inactive Hold :0
SIP1 Enable SCA    :0
SIP1 Sub CallPark  :0
SIP1 Hoteling Event:0
SIP1 Sub CC Status :0
SIP1 CSTA Number   :
SIP1 Feature Sync  :0
SIP1 Req With Port :1
SIP1 Enable Mute   :0
SIP1 VQ Name       :
SIP1 VQ Server     :
SIP1 VQ Server Port:5060
SIP1 VQ HTTP Server:
SIP1 Unreg Reboot  :0
SIP1 Flash Mode    :0
SIP1 Use Tel Call  :0
SIP1 Content Type  :
SIP1 Content Body  :
SIP1 Deal 180      :1
SIP1 Ena MAC Header:0
SIP1 Ena REG MAC   :0
SIP1 BLF dialog mat:1
<<END OF FILE>>
 

Each element is populated with a value.

...

OptionValuesDescription
SIP PortInteger, 1-65535, Defaults to 5060Sets the local SIP signaling port used by the phone. Defaults to 5060
STUN ServerIPv4 Address or HostnameSets the IPv4 Address or Hostname of the STUN server.
STUN PortInteger, 1-65535, Defaults to 3478Sets the port of the STUN server. Defaults to 3478.
STUN Refresh TimeInteger, in seconds, Defaults to 50Sets the STUN server refresh time, at which the phone will send a binding request period. Defaults to 50.
SIP Wait Stun TimeInteger, in milliseconds, Defaults to 800Sets the amount of the, in milliseconds, the phone should wait for the STUN server to respond before continuing. Defaults to 800.
Extern NAT AddrsIPv4 AddressIf the phone is configured to use STUN, the SIP Contact address will be set according to this option.
Reg Fail IntervalInteger, in seconds, Defaults to 32.Sets the time, after a failed registration, after reaching the halfway point of this interval time, at which the phone will attempt registration again. Defaults to 32.
SIP Pswd EncryptionBoolean, Defaults to 0If enabled, the phone's configuration file will be encrypted. Defaults to 0.
Strict BranchPrefixBoolean, Defaults to 0If enabled, when the phone receives a SIP message with a branch field that does not begin with z9hG4bk, the phone will return a 4xx message. Defaults to 0
Enable Group BackupBoolean, Defaults to 0If enabled, and the phone has both regular and backup registrars configured, the phone will, upon a failure to register with either of the registrars, unregister from both. If disabled, the phone will attempt to register with both, and the registration of one will not affect the registration with another. Defaults to 0.
Enable RFC4475Boolean, Defaults to 1If enabled, and the phone receives a SIP message with a From or To field containing a blank space, quotation marks, or both, the phone will reject the message. Defaults to 1.
SIP invite strictBoolean, Defaults to 1If disabled, the phone will allow SIP requests from servers to which it is not registered. Defaults to 1.
Notify RebootBoolean, Defaults to 0If disabled, the phone will not reboot when receiving a check-sync NOTIFY. Defaults to 0.
SMS direct EnabledBoolean, Defaults to 0If enabled, the phone will display the details of a text message when a new message is received.
SMS Save EnabledBoolean, Defaults to 1If disabled, the phone will not save received text message.
SMB Ring EnabledBoolean, Defaults to 1If disabled, the phone will not play a ringing tone when receiving an incoming text message.
CSTA EnableBoolean, Defaults to 0If enabled, the phone will be controllable using uaCSTA. Defaults to 0.
Strict UA MatchBoolean, Defaults to 0If enabled, the phone will only accepts requests from the registered-to server.
SIP Line List and SIP Line List Entry Elements

...

Expand
Code Block
borderStylesolid
titleSIP Line List and SIP Line List Entry Element Examples
<<VOIP CONFIG FILE>>
<SIP CONFIG MODULE>
--SIP Line List--  :
SIP1 Phone Number  :
SIP1 Display Name  :
SIP1 Sip Name      :
SIP1 Register Addr :
SIP1 Register Port :5060
SIP1 Register User :
SIP1 Register Pswd :
SIP1 Register TTL  :3600
SIP1 Enable Reg    :0
SIP1 Proxy Addr    :
SIP1 Proxy Port    :5060
SIP1 Proxy User    :
SIP1 Proxy Pswd    :
SIP1 BakProxy Addr :
SIP1 BakProxy Port :5060
SIP1 Enable Failbac:0
SIP1 Signal Crypto :0
SIP1 SigCrypto Key :
SIP1 Media Crypto  :0
SIP1 MedCrypto Key :
SIP1 SRTP Auth-Tag :0
SIP1 Local Domain  :
SIP1 Always FWD    :0
SIP1 Busy FWD      :0
SIP1 No Answer FWD :0
SIP1 Always FWD Num:
SIP1 Busy FWD Num  :
SIP1 NoAnswer FWD N:
SIP1 FWD Timer     :5
SIP1 Ring Type     :0
SIP1 Hotline Num   :
SIP1 Enable Hotline:0
SIP1 WarmLine Time :0
SIP1 Pickup Num    :
SIP1 Join Num      :
SIP1 NAT UDPUpdate :2
SIP1 UDPUpdate TTL :30
SIP1 Server Type   :0
SIP1 User Agent    :
SIP1 PRACK         :1
SIP1 Keep AUTH     :0
SIP1 Session Timer :0
SIP1 S.Timer Expire:0
SIP1 Enable GRUU   :0
SIP1 DTMF Mode     :3
SIP1 DTMF Info Mode:0
SIP1 NAT Type      :0
SIP1 Enable Rport  :1
SIP1 Subscribe     :0
SIP1 Sub Expire    :3600
SIP1 Single Codec  :0
SIP1 CLIR          :0
SIP1 Strict Proxy  :0
SIP1 Direct Contact:0
SIP1 History Info  :0
SIP1 DNS SRV       :0
SIP1 DNS Mode      :0
SIP1 XFER Expire   :0
SIP1 Ban Anonymous :0
SIP1 Dial Off Line :0
SIP1 Quota Name    :0
SIP1 Presence Mode :0
SIP1 RFC Ver       :1
SIP1 Signal Port   :5060
SIP1 Transport     :0
SIP1 Enable ChgPort:1
SIP1 TLS Version   :0
SIP1 Use SRV Mixer :0
SIP1 SRV Mixer Uri :
SIP1 Long Contact  :0
SIP1 Auto TCP      :0
SIP1 Uri Escaped   :1
SIP1 Click to Talk :0
SIP1 MWI Num       :
SIP1 CallPark Num  :
SIP1 Retrieve Num  :
SIP1 MSRPHelp Num  :
SIP1 User Is Phone :1
SIP1 Auto Answer   :0
SIP1 NoAnswerTime  :5
SIP1 MissedCallLog :1
SIP1 SvcCode Mode  :0
SIP1 DNDOn SvcCode :
SIP1 DNDOff SvcCode:
SIP1 CFUOn SvcCode :
SIP1 CFUOff SvcCode:
SIP1 CFBOn SvcCode :
SIP1 CFBOff SvcCode:
SIP1 CFNOn SvcCode :
SIP1 CFNOff SvcCode:
SIP1 ANCOn SvcCode :
SIP1 ANCOff SvcCode:
SIP1 Send ANOn Code:
SIP1 Send ANOffCode:
SIP1 CW On Code    :
SIP1 CW Off Code   :
SIP1 VoiceCodecMap :G722,G711U,G711A,G729,G726-32,G723
SIP1 BLFList Uri   :
SIP1 BLF Server    :
SIP1 Respond 182   :0
SIP1 Enable BLFList:0
SIP1 Caller Id Type:4
SIP1 Syn Clock Time:0
SIP1 Use VPN       :1
SIP1 Enable DND    :0
SIP1 Update Reg Exp:1
SIP1 Inactive Hold :0
SIP1 Enable SCA    :0
SIP1 Sub CallPark  :0
SIP1 Hoteling Event:0
SIP1 Sub CC Status :0
SIP1 CSTA Number   :
SIP1 Feature Sync  :0
SIP1 Req With Port :1
SIP1 Enable Mute   :0
SIP1 VQ Name       :
SIP1 VQ Server     :
SIP1 VQ Server Port:5060
SIP1 VQ HTTP Server:
SIP1 Unreg Reboot  :0
SIP1 Flash Mode    :0
SIP1 Use Tel Call  :0
SIP1 Content Type  :
SIP1 Content Body  :
SIP1 Deal 180      :1
SIP1 Ena MAC Header:0
SIP1 Ena REG MAC   :0
SIP1 BLF dialog mat:1
<<END OF FILE>>
 

Option

Values

Description

ID

SIP1, SIP2
SIP3, SIP4 (A25-only)

Sets the SIP line (1-4) to which the configuration settings should be applied.

Phone Number

String

Sets the identifier used for the user part of the From and To lines in the phone's SIP messaging.

Display NameStringSets the quoted string name identifier used in the From and To (REGISTER only) in the phone's SIP messaging.
Sip NameStringSets a name for the SIP line, visible within the web admin UI of the phone.
Register AddrIPv4 Address or HostnameSets the IPv4 address or hostname of the SIP Registrar.
Register PortInteger, 1-65535, Defaults to 5060Sets the port used to contact the SIP Registrar. Defaults to 5060
Register UserStringSets the SIP authentication user.
Register PswdStringSets the SIP authentication password.
Register TTLInteger, in seconds, Defaults to 3600Sets the default Expires timer for SIP registration. Defaults to 3600.
Enable RegBoolean, Defaults to 0Enables or disables SIP registration for this line.
Proxy AddrIPv4 Address or HostnameSets the IPv4 address or hostname for the SIP proxy. Defaults to none.
Proxy PortInteger, 1-65535, Defaults to 5060Sets the port used to contact the SIP Proxy. Defaults to 5060.
Proxy UserStringSets the SIP proxy authentication user.
Proxy PswdStringSets the SIP proxy authentication password.
BakProxy AddrIPv4 Address or HostnameSets the IPv4 address or hostname for the backup SIP Proxy. Defaults to none.
BakProxy PortInteger, 1-65535, Defaults to 5060Sets the port used to contact the backup SIP Proxy. Defaults to 5060.
Enable FailbacBoolean, Defaults to 0Sets whether the phone, whereby it is configured with both a primary and a backup proxy, should, whereupon detection that the primary proxy is operational again after having previously failed, resume sending calls to the primary server. If enabled, the phone will switch back to the primary proxy. If disabled, the phone will continue to send calls to the backup. Defaults to 0.
Signal CryptoBoolean, Defaults to 0If enabled, causes the phone to encrypt SIP signaling. Defaults to 0.
SigCrypto KeyStringSets the key used to encrypt SIP signaling.
Media CryptoBoolean, Defaults to 0If enabled, causes the phone to encrypt RTP media. Defaults to 0.
MedCrypto KeyStringSets the key used to encrypt RTP media.
SRTP Auth-TagInteger, Defaults to 0If set to 0, the phone will utilizes 80 byte SRTP tags, encrypting RTP using AES_CM_128_HMAC_SHA_80. If set to 1, the phone will utilize 32 byte SRTP tags, encrypting RTP using AES_CM_128_HMAC_SHA_32. Defaults to 0.
Local DomainStringSets the domain name used in SIP registration.
Always FWDBoolean, Defaults to 0If enabled, the phone will unconditionally forward calls. Defaults to 0.
Busy FWDBoolean, Defaults to 0If enabled, the phone will forward calls whenever it is busy. Defaults to 0.
No Answer FWDBoolean, Defaults to 0If enabled, the phone will forward calls that are not answered. Defaults to 0.
Always FWD NumStringSets the forwarding number used in conjunction with the Always FWD option.
Busy FWD NumStringSets the forwarding number used in conjunction with the Busy FWD option.
NoAnswer FWD NStringSets the forwarding number used in conjunction with the No Answer FWD option.
FWD TimerInteger, in seconds, Defaults to 5Sets the time, in seconds, applied to the No Answer FWD option. Defaults to 5.
Ring TypeInteger, 0-9, Defaults to 0Sets the ring type. If 0, use the default ring type. Otherwise, use the assigned ringing type tones. Defaults to 0.
Hotline NumStringSets the number to be dialed when the off-hook time is greater than the WarmLine Time and Enable Hotline is enabled.
Enable HotlineBoolean, Defaults to 0If enabled, and the phone has been off-hook longer than the WarmLine_Time, the phone will automatically dial the number defined by Hotline Num.
WarmLine TimeInteger, in seconds, 0-9, Defaults to 0Sets the amount of time the phone must remain off-hook before attempting to execute Hotline functionality.
Pickup NumStringSets the dialing prefix applied to calls that are picked up using function keys configured for Pickup functionality.
Join NumStringSets the dialing prefix applied to calls that are joined using function keys configured for Join functionality.
NAT UDPUpdateInteger, 0-2, Defaults to 2If set to 1, the phone will send SIP OPTION packets to the server after each UDPUpdate TTL time. If set to 2, the phone will send a CRLF to the server after each UDPUpdate TTL time. If set to 0, the phone will send nothing. Defaults to 2.
UDPUpdate TTLInteger, in seconds, Defaults to 30Sets the timer used by the NAT UDPUpdate option.
Server Type0, 1, 6, 14, 17, 22, 23, 24, 26, 28, 29, 30, 31, 33. Defaults to 0

Sets special compatibility settings required for specific server types. The following types are supported:

3CX - 31
BOTE - 6
BroadSoft - 28
Cellcom - 30
COMMON - 0
CONFIG - 23 
Epygi - 33
FUJITSU - 24
Karel UCAP - 29
MITEL - 17
MS_RP - 22
NET2PHONE - 1
NORTEL - 14
SOFTX3000 - 26

Defaults to 0. 

User AgentStringSets the SIP User-Agent passed by the phone when communicating.
PRACKBoolean, Defaults to 1Enables or disables SIP PRACK functionality within the phone. Defaults to 1.
Keep AUTHBoolean, Defaults to 0If enabled, the phone will, on SIP re-registration, send authentication in the initial REGISTER rather than waiting to send it after receiving a 401 Unauthorized message. Defaults to 0.
Session TimerBoolean, Defaults to 0If enabled, the phone will send SIP session timers throughout the call, ending the call when there is no reply. Defaults to 0.
S.Timer ExpireInteger, in seconds, Defaults to 0Sets the SIP Session timer timeout value in seconds. Defaults to 0
Enable GRUUBoolean, Defaults to 0If enabled, the phone will append GRUU information to the Contact header of INVITEs. Defaults to 0.
DTMF ModeInteger, 0-3, Defaults to 3

Sets the DTMF method to be used by the phone, as follows:

Inband - 0
RFC2833 - 1
SIP INFO - 2
Auto - 3 

Defaults to 3.

DTMF Info ModeInteger, 0-1, Defaults to 0If set to 1, and the phone is configured for SIP INFO DTMF, the * and # keypresses will send "*" and "#" respectively. If set to 0, and the phone is configured for SIP INFO DTMF, the * and # keypresses will send as 10 and 11 respectively. Defaults to 0.
NAT TypeBoolean, Defaults to 0If enabled, STUN will be used. Defaults to 0.
Enable RportBoolean, Defaults to 1If disabled, the phone will not send rport to assist with NAT traversal as per RFC3581. Defaults to 1.
SubscribeBoolean, Defaults to 0If enabled, the phone will subscribe for Message Waiting Indicator (MWI). Defaults to 0.
Sub ExpireInteger, in seconds, Defaults to 3600The timer at half-of-which, the phone will re-subscribe. Defaults to 3600.
Single CodecBoolean, Defaults to 0If enabled, the phone will respond to SIP messages with only one codec, rather than with all codec capabilities. Defaults to 0.
CLIRInteger, 0-2, Defaults to 0Specifies the method of anonymous calling to use. When set to 0, the phone calls normally. When set to 1, the phone calls anonymously according to RFC3323. When set to 2, the phone calls anonymously according to RFC3325.
Strict ProxyBoolean, Defaults to 0When enabled, respond using the source address, not the Via address. Defaults to 0.
Direct ContactBoolean, Defaults to 0When enabled, attempt to directly communicate with the called party, not using the intermediary proxy or UA. Defaults to 0.
History InfoBoolean, Defaults to 0When enabled, call history information for the line will be provided. Defaults to 0. This configuration item is currently unused.
DNS SRVBoolean, Defaults to 0If enabled, the phone will perform DNS SRV resolution for outgoing requests. Defaults to 0.
DNS ModeInteger, 0-2, Defaults to 0Sets the type of host resolution to perform. When set to 0, the phone will use A records. When set to 1, the phone will use SRV records. When set to 2, the phone will use NAPTR records.
XFER ExpireInteger, in seconds, Defaults to 0Specifies the time, in seconds, after which the phone will send a BYE following attended transfer hang up.
Ban AnonymousBoolean, Defaults to 0When enabled, the phone will reject anonymous calls. Defaults to 0.
Dial Off LineBoolean, Defaults to 0If enabled, the phone will attempt to place outgoing calls, even when it is unregistered. If disabled, the phone will not be able to place outgoing calls when it is unregistered. Defaults to 0.
Quota NameBoolean, Defaults to 0If enabled, the phone will encapsulate the Display Name that it sends in SIP signaling inside of quotation marks. Defaults to 0.
Presence ModeBoolean, Defaults to 0When enabled, the phone utilizes special presence handling for Wuchuan servers. Defaults to 0.
RFC VerInteger, 0-1, Defaults to 1Specifies the SIP signaling RFC standard to utilize. When set to 0, the phone will communicate using RFC2543 compliant signaling. When set to 1, the phone will communicate using RFC3261 compliant signaling. Defaults to 1.
Signal PortInteger, Defaults to 5060Sets the phone's local SIP signaling port. Defaults to 5060.
TransportInteger, 0, 1, 3, Defaults to 0

Sets the transport type for SIP signaling.
UDP - 0
TCP - 1
TLS - 3
Signal Transport option is no longer used as of this firmware version and Transport replaces its functionality. 

Enable ChgPortBoolean, Defaults to 1If enabled, the phone will attempt to dynamically change its local SIP port in order to work around SIP Router ALG issues. Defaults to 1.
TLS VersionInteger, 0-2, Defaults to 0

Sets the type of TLS protocol version to be used:

TLS 1.0 - 0
TLS 1.1 - 1
TLS 1.2 - 2 

Defaults to 0.

Use SRV MixerBoolean, Defaults to 0When enabled, the phone utilizes server-side conferencing support. Defaults to 0.
SRV Mixer UriStringSets the URI to be used for server-side conferencing when the Use SRV Mixer option is enabled.
Long ContactBoolean, Defaults to 0If enabled, allows the phone to process long Contact fields. Defaults to 0.
Auto TCPBoolean, Defaults to 0When enabled, if the packet size of a UDP signaling packet is to exceed 1300 bytes, automatically use TCP transport. Defaults to 0.
Uri EscapedBoolean, Defaults to 1If disabled, the phone will not escape # characters into "%23" when creating URIs. While this option is enabled, the rule to send numbers when pressing the # key should be disabled.
Click to TalkBoolean, Defaults to 0If enabled, the phone can make a call by itself receiving an incoming REFER message. Defaults to 0.
MWI NumStringSets the number to dial for voicemail.
CallPark NumStringSets the number to dial for call parking.
Retrieve NumStringSets the number to dial for call retrieval for Broadsoft environments.
MSRPHelp NumStringFor MS_RP_BU servers, sets a number to be called after a successful transfer.
User Is PhoneBoolean, Defaults to 1If disabled, the phone will not append the ";user=phone" parameter to SIP messages.
Auto AnswerBoolean, Defaults to 0If enabled, and if the NoAnswerTime has elapsed, the phone will automatically answer an incoming call. Defaults to 0.
NoAnswerTimeInteger, in seconds, defaults to 5Sets the amount of time, in seconds, the phone should wait on an incoming call before proceeding to Auto Answer, if Auto Answer is enabled. Defaults to 5.
MissedCallLogBoolean, Defaults to 1If disabled, the phone will not record call logs. Defaults to 1.
SvcCode ModeBoolean, Defaults to 0If enabled, the phone will allow the sending of service codes (numbers) to the SIP server, depending on the enabling/disabling of certain functions on the phone. Defaults to 0.
DNDOn SvcCodeStringSets the number to send to the server when DND is enabled on the phone.
DNDOff SvcCodeStringSets the number to send to the server when DND is disabled on the phone.
CFUOn SvcCodeStringSets the number to send to the server when Call Forward Unconditional is enabled on the phone.
CFUOff SvcCodeStringSets the number to send to the server when Call Forward Unconditional is disabled on the phone.
CFBOn SvcCodeStringSets the number to send to the server when Call Forward Busy is enabled on the phone.
CFBOff SvcCodeStringSets the number to send to the server when Call Forward Busy is disabled on the phone.
CFNOn SvcCodeStringSets the number to send to the server when Call Forward on No Answer is enabled on the phone.
CFNOff SvcCodeStringSets the number to send to the server when Call Forward on No Answer is disabled on the phone.
ANCOn SvcCodeStringSets the number to send to the server when Anonymous Call Banning is enabled on the phone.
ANCOff SvcCodeStringSets the number to send to the server when Anonymous Call Banning is disabled on the phone.
Send ANOn CodeStringSets the number to send to the server when Anonymous Calling is enabled on the phone.
Send ANOffCodeStringSets the number to send to the server when Anonymous Calling is disabled on the phone.
CW On CodeStringSets the number to send to the server when Call Waiting is enabled on the phone.
CW Off CodeStringSets the number to send to the server when Call Waiting is disabled on the phone.
VoiceCodecMap

Comma-separated list of:
G722, G711U, G711A, G729, G726-32, G723

Sets the voice codecs used for this line.
BLFList UriStringSpecifies the BLF Resource List to which the phone should subscribe. Multiple lists are supported, separated by commas.
BLF ServerIPv4 Address or HostnameIf the server to which the phone is registered does not support BLF Resource List subscription package, sets the address of the BLF Resource List server.
Respond 182Boolean, Defaults to 0If enabled, the phone will, when it's already on call and an additional call comes in, send a 182 Queued SIP message to the SIP server. If disabled, the phone sends a 180. Defaults to 0.
Enable BLFListBoolean, Defaults to 0If enabled, the phone will subscribe for BLF Resource List.
Caller Id TypeInteger, 1-5, Defaults to 4

Sets the priority of the incoming Caller ID:
FROM header - 1
P-Asserted-Identity header, followed by FROM header - 2
Remote-Party-ID header, followed by FROM header - 3
P-Asserted-Identity header, followed by Remote-Party-ID header, followed by FROM header - 4
Remote-Party-ID header, followed by P-Asserted-Identity-Header, followed by FROM header - 5

Syn Clock TimeBoolean, Defaults to 0If enabled, the phone will set its clock according to the Date field in the 200 OK following a successful REGISTER. Defaults to 0.
Use VPNBoolean, Defaults to 1If disabled, and the phone is connected to a VPN, the phone will not initiate REGISTER using the VPN IP address. If enabled, the phone will, when connected to a VPN, use the VPN IP address to initiate the REGISTER. Defaults to 1.
Enable DNDBoolean, Defaults to 0If enabled, the phone will not accept incoming calls from this SIP line. Defaults to 0.
Update Reg ExpBoolean, Defaults to 1If disabled, the phone will not update its registration expiration with the Expires value from the 200 OK that the server sends in response to a successful registration. Defaults to 1.
Inactive HoldBoolean, Defaults to 0If enabled, the phone will send "a=inactive" in the INVITE sent after a call is placed on hold. If disabled, the phone will send "a=sendonly" in the INVITE sent after a call is placed on hold. Defaults to 0.
Enable SCABoolean, Defaults to 0Enables support for the Broadsoft SCA feature. Defaults to 0.
Sub CallParkString, Defaults to 0Sets the Call Parking subscribed number for Broadsoft servers. Defaults to 0.
Hoteling EventBoolean, Defaults to 0If enabled, subscribes for Broadsoft Hotel agent service. Defaults to 0.
Sub CC StatusBoolean, Defaults to 0If enabled, subscribes to the Broadsoft call center service. Defaults to 0.
CSTA NumberStringSets the number/URI for the uaCSTA server.
Feature SyncBoolean, Defaults to 0Enables support for Broadsoft Feature Sync. Defaults to 0.
Req With PortBoolean, Defaults to 1If disabled, do not send port in SIP messages to the server. Defaults to 1.
Enable MuteBoolean, Defaults to 0If enabled, mutes the phone during intercom calls. Defaults to 0.
VQ NameStringSets an identifier for the voice quality server.
VQ ServerIPv4 Address or HostnameSets the IPv4 Address or hostname of the voice quality server.
VQ Server PortInteger, 1-65535, Defaults to 5060Sets the port used by the voice quality server.
VQ HTTP ServerURLSets the HTTP URL of the voice quality server.
Unreg RebootBoolean, Defaults to 0If enabled, the phone will send unregisters to any registered servers after it reboots, before it attempts to register. Defaults to 0.
Flash ModeInteger, 0-1, Defaults to 0If set to 0, flash is handled locally on the phone. If set to 1, the phone will send a SIP INFO message indicating the flash event to the server, with data defined by Content Type and Content Body
Use Tel CallBoolean, Defaults to 0If enabled, the phone will replace "sip" in its URIs with "tel"
Content TypeStringSets the content type data used when the phone sends SIP INFO flash messages to the server.
Content BodyStringSets the body of the data used when the phone sends SIP INFO flash messages to the server.
Deal 180Boolean, Defaults to 0If disabled, the phone will not generate local ringback on 180, instead depending on inband RTP ringback provided by the remote party.
Ena MAC HeaderBoolean, Defaults to 0If enabled, the phone will send its MAC with its SIP messaging to the server
Ena REG MACBoolean, Defaults to 0If enabled, the phone will send its MAC when sending REGISTER to the server
BLF dialog matBoolean, Defaults to 1If disabled, the phone will not strictly check BLF dialog versions.

MCAST CFG MODULE Elements

...

Expand
Code Block
borderStylesolid
titleTXT QOS CONFIG MODULE Elements
<<VOIP CONFIG FILE>>
 
<QOS CONFIG MODULE>
Enable VLAN        :0
Enable diffServ    :1
LLDP Transmit      :1
LLDP Refresh Time  :60
LLDP Learn Policy  :1
CDP Enabled        :0
CDP Refresh Time   :60
Singalling DSCP    :-1
Voice DSCP         :46
VLAN ID            :256
Signalling Priority:0
Voice Priority     :0
LAN Port Priority  :0
VLAN Recv Check    :1
Enable PVID        :1
PVID Value         :254
DHCP Option Vlan   :0
<<END OF FILE>>

...

Option

Values

Description

Enable VLAN

Boolean, Defaults to 0

If enabled, the phone will perform VLAN assignment of itself and its PC port.. Defaults to 0.

Enable diffServBoolean, Defaults to 1If enabled, the phone will perform DSCP tagging. Defaults to 1.
LLDP TransmitBoolean, Defaults to 1If disabled, the phone will not transmit LLDP packets to the switch. Defaults to 1.
LLDP Refresh TimeInteger, in seconds, Defaults to 60Sets the interval, in seconds, at which the phone will transmit LLDP packets. Defaults to 60.
LLDP Learn PolicyBoolean, Defaults to 1If disabled, the phone will not learn its VLAN settings using LLDP-MED TLV. Defaults to 1.
CDP EnabledBoolean, Defaults to 0If enabled, the phone will send CDP packets. Defaults to 0.
CDP Refresh TimeInteger, in seconds, Defaults to 60Sets the period at which CDP packets will be sent from the phone.
Singalling DSCPDefaults to -1Sets the DSCP value for SIP signaling. Defaults to -1.
Voice DSCPInteger, Defaults to 46Sets the DSCP value for RTP media. Defaults to 46.
VLAN IDInteger, 0-4095, Defaults to 256Sets the VLAN ID to which the phone should bind itself. Defaults to 256.
Signalling PriorityInteger, 0-7. Defaults to 0.Sets the 802.1p COS bit for SIP Signaling. Defaults to 0.
Voice PriorityInteger, 0-7. Defaults to 0.Sets the 802.1p COS bit for RTP Media. Defaults to 0.
LAN Port PriorityInteger, 0-7. Defaults to 0.Sets the 802.1p priority bit for traffic engrossing the LAN port. Defaults to 0.
VLAN Recv CheckBoolean, Defaults to 1If enabled, the phone will compare the VLAN ID of LAN port packets and will not process them if they match the PC port packets. Defaults to 1.
Enable PVIDBoolean, Defaults to 1If enabled, the phone will tag the PC port with the VLAN assigned by PVID Value. Defaults to 1.
PVID ValueInteger, 0-4095. Defaults to 254.Sets the PC port VLAN ID. Defaults to 254.
DHCP Option VlanInteger, Defaults to 0If set to 0, the phone will not retrieve its VLAN from DHCP. If set to an option, 128-254, the phone will respond to the named DHCP Option.

...

Expand
Code Block
borderStylesolid
titleTXT PHONE CONFIG MODULE Elements
<<VOIP CONFIG FILE>>
 
<PHONE CONFIG MODULE>
Menu Password      :789
KeyLock Password   :123
Fast Keylock Code  :
Enable KeyLock     :0
KeyLock Status     :0
Emergency Call     :110
LCD Title          :Asterisk
LCD Constrast      :5
LCD Luminance      :1
Backlight Off Time :30
ScrnSaver Wait Time:0
KeyLock Timeout    :0
Enable Power Led   :0
SMS MWI Power Led  :0
Miss Call Power Led:0
Talk Dial Power Led:0
Ringing Power Led  :0
Mute Call Power Led:0
Hold Power Led     :0
Time Display Style :0
Phone Model        :A25
FuncKey Page Num   :2
Blf Default type   :0
Alarm  Clock       :0,,1
Disable CHN IME    :0
Disable Dial Search:0
Redial Enter CLog  :1
Date Display Style :0
Date Separator     :0
Enable Pre-Dial    :1
Default Line       :0
Enable Default Line:0
Enable Auto SelLine:1
Agent Username     :
Agent Password     :
Agent Number       :
Agent Sipline      :0
Agent Status       :0
Agent Status Reason:
--BW Calllogs Conf-:
BWCLog1 Title      :
BWCLog1 URL        :
BWCLog1 Username   :
BWCLog1 Password   :
BWCLog1 SipLine    :0
--BW Directory Conf:
BWDir1 Title       :
BWDir1 URL         :
BWDir1 Username    :
BWDir1 Password    :
BWDir1 SipLine     :0
--LDAP Config--    :
LDAP1 Title        :
LDAP1 Server       :
LDAP1 port         :389
LDAP1 Authenticate :0
LDAP1 Version      :3
LDAP1 Calling Line :0
LDAP1 Enable Search:0
LDAP1 Bind Line    :0
LDAP1 Base         :
LDAP1 Username     :
LDAP1 Password     :
LDAP1 Tel Attr     :telephoneNumber
LDAP1 Mobile Attr  :mobile
LDAP1 Other Attr   :home
LDAP1 Displayname  :cn
LDAP1 Filter Name  :
LDAP1 Filter number:
--Xml PhoneBook--  :
XML-PBook1 Name    :
XML-PBook1 Addr    :
XML-PBook1 Auth    :
XML-PBook1 Policy  :0
XML-PBook1 Sipline :0
XMl-PBook1 BindLine:0
Phonebook Groups   :
--Function Key--   :
Fkey1 Type         :2
Fkey1 Value        :SIP1
Fkey1 Title        :
--Soft Dss Key--   :
SoftFkey1 Type     :0
SoftFkey1 Value    :
SoftFkey1 Title    :
Ui font Color      :0xFFFFFF$0x444343
Ui Title Color     :0x000026$0x4f79a7
Ui Softkey Color   :up:0x5e6f85$0x485972@ down:0x00$0xffc83b
Ui List  Color     :0x00$0xa9c1c9
Ui Balloon Color   :0x00$0x6c7b8d
Ui Second Color    :odd:0xc9d9eb$0x9fc0e3@ even:0x356291$0x7296bb@ select:0x34373c$0xe2a917@ interval:0x4478ae@ LSKbgc:0x6b84aa
Ui ScrnSaver Color :0x00$0x808080
Vqm Display Order  :
DSS Home Page      :0
Download Pb search :0
<<END OF FILE>>

Each element is populated with a value.

...

Option

Values

Description

Menu Password

Integer, Defaults to 789

Sets the password used to access the phone's password-protected advanced menu setting. Defaults to 789.

KeyLock PasswordInteger, Defaults to 123Sets the password used to unlock the phone when key lock has been engaged
Fast Keylock CodeIntegerSets a key sequence that, when entered, immediately locks the phone.
Enable KeyLockBoolean, Defaults to 0If enabled, allows locking of the phone. Defaults to 0.
KeyLock Status

0, 1

Displays the phone's locked status. 0 for unlocked, 1 for locked.
Emergency CallStringSets a number the phone is allowed to call, even while locked.
LCD TitleString, Defaults to AsteriskSets the text displayed in the idle screen status bar. Defaults to Asterisk
LCD ConstrastInteger, 1-10, Defaults to 5Sets the display's contrast level. Obsolete.
LCD LuminanceBoolean, Defaults to 1If disabled, the phone's backlight will not be list. Defaults to 1.
Backlight Off TimeInteger, in seconds, Defaults to 30Sets the time, in seconds, at which the phone will turn its backlight off. Defaults to 30. SUGGEST A LONGER TIME, E.G. 15 MINUTES
ScrnSaver Wait TimeInteger, in seconds, Defaults to 0Sets the time, zero is off, at which the screensaver will engage. Defaults to 0.
KeyLock TimeoutInteger, in seconds, Defaults to 0If greater than 1, sets a timer that, when reached, causes the phone to automatically lock its keypad.
Enable Power LedBoolean, Defaults to 0If enabled, the MWI LED will turn on when idle, flash red on incoming calls, and flash slowly on missed calls / waiting messages. Defaults to 0.
SMS MWI Power LedBoolean, Defaults to 0If enabled, the MWI LED will turn on when a new MESSAGE has been received. Defaults to 0.
Miss Call Power LedBoolean, Defaults to 0If enabled, the MWI LED will turn on when a missed call is received. Defaults to 0.
Talk Dial Power LedBoolean, Defaults to 0If enabled, the MWI LED will turn on when the phone is on a call. Defaults to 0.
Ringing Power LedBoolean, Defaults to 0If enabled, the MWI LED will turn on when the phone is ringing. Defaults to 0.
Mute Call Power LedBoolean, Defaults to 0If enabled, the MWI LED will turn on when the phone is muted. Defaults to 0.
Hold Power LedBoolean, Defaults to 0If enabled, the MWI LED will turn on when a caller is placed on hold. Defaults to 0.
Time Display StyleInteger, 0-1, Defaults to 0When 0, display time in 24-hour format. When 1, display time in 12-hour format. Defaults to 0. SUGGEST DEFAULTING TO 12-HOUR
Phone ModelString, Defaults to A20, A22 or A25Shows the phone model. Defaults to A20, A22 or A25
FuncKey Page NumInteger, Defaults to 1Specifies the number of pages of BLF keys that the phone is to display. Defaults to 1.
Blf Default typeInteger, 0-2, Defaults to 0

Sets the default transfer function of the BLF keys:

None - 0
Blind - 1
Attended - 2 

Alarm Clock0,,1Enables the alarm clock. The default value is 0,,1
Disable CHN IMEBoolean, Defaults to 0Enables preventing Chinese Input methods. Defaults to 0.
Disable Dial SearchBoolean, Defaults to 0If enabled, prevents searching and number matching during dialing. Defaults to 0.
Redial Enter ClogInteger, 0-1, Defaults to 1If set to 0, the redial button will dial the last number dialed. If set to 1, the phone will enter the call log and display recently dialed numbers. Defaults to 1.
Date Display StyleInteger, 0-13, Defaults to 0

Sets the date display formatting that should be used by the phone as follows:

1 JAN MON - 0
JAN 1 MON - 1
MON 1 JAN - 2
MON JAN 1 - 3
DD MM YY - 4
DD MM YYYY - 5
MM DD YY - 6
MM DD YYYY - 7
YY MM DD - 8
YYYY MM DD - 9
1 January Monday - 10
January 1 Monday - 11
Monday 1 January - 12
Monday January 1 - 13 

Date SeparatorInteger 0-3, Defaults to 0

Sets the date display separator that should be used by the phone as follows:

/, 0
-, 1
., 2
(space character), 3 

Enable Pre-DialBoolean, Defaults to 1If disabled, the phone will go off-hook as soon as DTMF is entered, and off-hook dialing rules will be active. Defaults to 1.
Default LineInteger, 0-1 or 0-3 (A25), Defaults to 0.Sets the line which the phone will, by default, use for outbound calling. Defaults to 1.
Enable Default LineBoolean, Defaults to 0If enabled, show, while the phone is idle, in the phone's greeting / status bar, the default line that will be used. Defaults to 0.
Enable Auto SelLineBoolean, Defaults to 1If disabled, do not automatically switch from an unregistered default line to a registered other line for outgoing calls. Defaults to 1.
Agent UsernameStringSets the Broadsoft agent username.
Agent PasswordStringSets the Broadsoft agent password.
Agent NumberStringSets the Broadsoft agent number.
Agent SiplineInteger, 0-1 or 0-4 (A25), Defaults to 0Sets the SIP line for Broadsoft agent login.
Agent StatusInteger, 0-4, Defaults to 0

Sets the Broadsoft agent status as follows:

LOGON - 0
LOGOFF - 1
UNAVILABLE - 2
AVAILABLE - 3
WRAPUP - 4 

Agent Status ReasonStringSets the Broadsoft agent status reason code.
Phonebook GroupsString where GroupName;0,OtherGroupName;0Contains a comma separated list of contact group names.
Ui font ColorDefaults to 0xFFFFFF$0x444343Sets the default UI color.
Ui Title ColorDefaults to 0x000026$0x4f79a7Sets the color of UI titles.
Ui Softkey ColorDefaults to up:0x5e6f85$0x485972@ down:0x00$0xffc83bSets the color of unpressed and pressed soft keys.
Ui List ColorDefaults to 0x00$0xa9c1c9Sets the color of UI lists.
Ui Balloon ColorDefaults to 0x00$0x6c7b8dSets the color of UI balloons.
Ui Second ColorDefaults to odd:0xc9d9eb$0x9fc0e3@ even:0x356291$0x7296bb@ select:0x34373c$0xe2a917@ interval:0x4478ae@ LSKbgc:0x6b84aaSets the color of rows in the UI.
Ui ScrnSaver ColorDefaults to 0x00$0x808080Sets the color of the screensaver in the UI.
Vqm Display OrderSemi-colon separated list of integers from 1-20

Sets the ordering of the displayed voice quality metrics within the UI as follows:

Start time - 1
Stop time - 2
Local user - 3
Remote user - 4
Local IP - 5
Remote IP - 6
Local port - 7
Remote port - 8
Local codec - 9
Remote codec - 10
Jitter - 11
Jitter Buffer Rate - 12
Jitter Buffer Max - 13
Packets lost - 14
Network Packet Loss rate - 15
MOS-LQ - 16
MOS-CQ - 17
Round Trip Delay - 18
End System Delay - 19
Symm One-Way Delay - 20

DSS Home PageInteger, Defaults to 0Sets the home page of any BLF keys. Defaults to 0.
Download Pb searchBoolean, Defaults to 0If enabled, the "get" command will be used when searching remote phonebooks.
BW Calllogs Conf and BW Calllogs Conf Entry Element

...

Expand
Code Block
borderStylesolid
titleLDAP Config and LDAP Config Entry Element Examples
<<VOIP CONFIG FILE>>
 
<PHONE CONFIG MODULE>
--LDAP Config--    :
LDAP1 Title        :
LDAP1 Server       :
LDAP1 port         :389
LDAP1 Authenticate :0
LDAP1 Version      :3
LDAP1 Calling Line :0
LDAP1 Enable Search:0
LDAP1 Bind Line    :0
LDAP1 Base         :
LDAP1 Username     :
LDAP1 Password     :
LDAP1 Tel Attr     :telephoneNumber
LDAP1 Mobile Attr  :mobile
LDAP1 Other Attr   :home
LDAP1 Displayname  :cn
LDAP1 Filter Name  :
LDAP1 Filter number:
<<END OF FILE>>

Option

Values

Description

ID

LDAP[n]

Sets an identifier for the LDAP phonebook where n is from 1-4.

TitleStringSets the displayed title of the remote LDAP phonebook.
ServerIPv4 Address or HostnameSets the IPv4 address or hostname of the LDAP server.
PortInteger, 0-4095, Defaults to 389Sets the port for contacting the LDAP server. Defaults to 389.
AuthenticateInteger, 0-3, Defaults to 3

Specifies the method of authentication to be used against the LDAP server as follows:

None - 0
Digest-MD5 - 1
CRAM-MD5 - 2
Simple - 3

Defaults to 3.

VersionInteger, 2-3, Defaults to 3Sets the LDAP protocol version to use when communication to the server. Defaults to 3.
Calling LineInteger, 0-2 or 0-4 (A25), Defaults to 0If 0, creating calls through the LDAP phonebook will be done via the current line. If the value is 1-4, use the corresponding SIP line to place the calls. Defaults to 0.
Enable SearchBoolean, Defaults to 0When enabled, query the LDAP server when outbound calls or made, or inbound calls are received. The contacts name will be searched against the LDAP server. The priority is the Local phonebook, followed by the LDAP phonebook, followed by the Display Name of the SIP endpoint. Defaults to 0.
Bind LineInteger, 0-2 or 0-4 (A25), Defaults to 0Sets the account for which LDAP searching for this LDAP config will bind
BaseStringSets the LDAP search root / base for queries.
UsernameStringSets the LDAP server authentication username.
PasswordStringSets the LDAP server authentication password.
Tel AttrString, defaults to telephoneNumberSets the LDAP attribute name to search for telephone numbers.
Mobile AttrString, defaults to mobileSets the LDAP attribute name to search for mobile numbers.
Other AttrStringSets an additional LDAP attribute name that can be searched for other numbers.
DisplaynameStringSets the name attribute that should be displayed on the phone.
Filter NameStringSets the LDAP search results filter for name filtering. A good example is (|(cn=%)(sn=%))
Filter numberStringSets the LDAP search results filter for number filtering. A good example is (|(telephoneNumber=%)(mobile=%)(other=%))

...

Expand
Code Block
borderStylesolid
titleXml Phonebook and Xml Phonebook Entry Element Examples
<<VOIP CONFIG FILE>>
 
<PHONE CONFIG MODULE>
--Xml PhoneBook--  :
XML-PBook1 Name    :
XML-PBook1 Addr    :
XML-PBook1 Auth    :
XML-PBook1 Policy  :0
XML-PBook1 Sipline :0
XML-PBook1 BindLine:0
Phonebook Groups   :
<<END OF FILE>>
 

Option

Values

Description

ID

XML-PBook[n]

Sets an identifier for the XML phonebook where n is from 1-8.

NameStringSets the displayed name of the remote phonebook.
AddrURL as stringSets the address of the remote phonebook.
AuthStringSets the username and password for retrieving the phonebook.
PolicyInteger, 0, 1, 2, 4, Defaults to 0

Sets the type of authentication used to retrieve the phonebook as follows:

Anonymous - 0
Digest MD5 - 1
CRAM MD5 - 2
Simple - 4

Defaults to 0 

SiplineInteger, 0-2 or 0-4 (A25)Sets the SIP line with which to associate the remote phonebook. If set to 0, use the current line. Otherwise, use the specified SIP line, from 1-4.
BindLineInteger, 0-2 or 0-4 (A25)Sets the SIP line for searching the remote phonebook. If set to 0, use the current line. Otherwise, use the specified SIP line, from 1-4.
Function Key and Function Key Entry Element

...

Expand
Code Block
borderStylesolid
titleTXT AUTOUPDATE CONFIG MODULE Elements
<<VOIP CONFIG FILE>>
 
<AUTOUPDATE CONFIG MODULE>
Download Username  :
Download Password  :
AP Pswd Encryption :0
FDPS Enable        :1
Config File Name   :
Config File Key    :
Common Cfg File Key:
Download Server IP :
Download Protocol  :0
Download Mode      :0
Download Interval  :1
DHCP Option        :66
Save DHCP Opion    :0
DHCP Option 120    :0
PNP Enable         :1
PNP IP             :224.0.1.75
PNP Port           :5060
PNP Transport      :0
PNP Interval       :1
Save Provision Info:0
Download CommonConf:1
Download DeviceConf:1
Check FailTimes    :5
update PB Interval :720
Clr PB B4 Import   :0
Trust Certification:0
Device Cert Mode   :1
Auto Server Digest :0
Enable Auto Upgrade:0
Upgrade Server 1   :
Upgrade Server 2   :
Auto Upgrade intval:24
<<END OF FILE>>
 

...

Option

Values

Description

Download Username

String

Sets the optional password that will be passed in when performing retrievals of provisioning files.

Download PasswordStringSets the optional password that will be passed in when performing retrievals of provisioning files.
AP Pswd EncryptionBoolean, Defaults to 0If enabled, the phone will disguise Auto Update module password. Defaults to 0.
FDPS EnableBoolean, Defaults to 1If disabled, does not contact FDPS server on-boot. Defaults to 1.
Config File Namenull, $mac.cfg, $input.cfgIf null, the phone will retrieve a file as <mac>.cfg. If set to $mac, the phone will also retrieve a file as <mac>.cfg. If set to $input.cfg, the phone will prompt the user on the screen to input the file name during boot.
Config File KeyStringSpecifies an AES key that must be used to decrypt the device configuration file.
Common Cfg File KeyStringSpecifies an AES key that must be used to decrypt the common configuration file. NEED TO GET LIST OF COMMON FILES
Download Server IPIPv4 Address or HostnameSpecifies the server address for retrieving configuration files.
Download ProtocolInteger, 0, 1, 2, 4, 5, Defaults to 0

Sets the protocol used to contact the provisioning server as follows:

Disabled - 0
FTP - 1
TFTP - 2
HTTP - 4
HTTPs - 5

Defaults to 0

Download ModeInteger, 0-2, Defaults to 0

Sets the provisioning upgrade type as follows:

Do not download the specified config file - 0
Download the specified config file after reboot - 1
Download the specified config file according to the Download Interval - 2 

Download IntervalInteger, in hours, Defaults to 1Sets the interval, in hours, at which the phone will download the configuration file if so-specified by Download Mode. Defaults to 1.
DHCP OptionInteger

Sets the method of DHCP option response as follows:

Disable DHCP option downloading - 0
Respond to DHCP option 66 - 66
Respond to DHCP option 43 - 43
Respond to custom option 128-254: 128-254

Defaults to 66 

Save DHCP OpionBoolean, Defaults to 0If enabled, the phone will store the DHCP-specified configuration. Defaults to 0.
DHCP Option 120Boolean, Defaults to 0If enabled, the phone will retrieve the SIP server address using DHCP Option 120. Defaults to 0.
PNP EnableBoolean, Defaults to 1If disabled, the phone will not attempt SIP uPNP for provisioning.
PNP IPIPv4 multicast address, Defaults to 224.0.1.75Specifies the IPv4 multicast address to which the phone should broadcast its SIP uPNP information.
PNP PortInteger, Defaults to 5060Specifies the port to which the phone should broadcast its SIP uPNP information.
PNP TransportInteger, Defaults to 0If 0, broadcast using UDP. If 1, broadcast using TCP.
PNP IntervalInteger, 1-99, in hours, Defaults to 1Specifies the interval at which the phone should broadcast its SIP uPNP information.
Save Provision InfoBoolean, Defaults to 0If enabled, the phone will save the auto provisioning information and re-use it after retrieving a new configuration. Defaults to 0.
Download CommonConfBoolean, Defaults to 1If disabled, the phone will only download its own configuration file, and not also attempt to download the common configuration file. Defaults to 1.
Download DeviceConfBoolean, Defaults to 1If disabled, the phone will only download the common configuration file, and not also attempt to download its device configuration file. Defaults to 1.
Check FailTimesInteger, Defaults to 5Specifies the number of time the phone will attempt to retrieve the provisioning information after failure before attempting to continue. Defaults to 5.
update PB IntervalInteger, in seconds, Defaults to 720Specifies the interval, in seconds, at which to update phonebooks. Defaults to 720.
Clr PB B4 ImportInteger, 0-1, Defaults to 0If set to 1, remove all contacts when downloading a phonebook from the provisioning server. Defaults to 0.
Trust CertificationInteger, 0-3, Defaults to 0.

Verify server-supplied SSL according to:

Do not verify - 0
Verify according to phone's default CA file - 1
Verify according to phone's user-supplied CA file - 2
Verify according to either phone's default CA file or phone's user-supplied CA file - 3 

Device Cert ModeInteger, 0-1, Defaults to 1When set to 0, the phone uses only built-in certificates for validation. When set to 1, the phone will use customer-provided certificates for validation.
Auto Server DigestBoolean, Defaults to 0When enabled, the phone will get digest from the server.
Enable Auto UpgradeBoolean, Defaults to 0If enabled, the phone will automatically upgrade to new firmware if provided
Upgrade Server 1StringSpecifies the location of the first firmware server.
Upgrade Server 2StringSpecifies the location of the second (backup) firmware server.
Auto Upgrade intvalInteger, in hours, Defaults to 24If Enable Auto Upgrade is enabled, the phone will perform the upgrade at the interval, in hours, defined by this option. Defaults to 24.
Auto etc UrlStringSpecifies the location of OpenVPN configuration files the phone should download.
Auto Image UrlStringSpecifies the location of a firmware file that the phone should download.
Auto Pbook UrlStringSpecifies the location of an XML phonebook the phone should download.

...

Expand
Code Block
borderStylesolid
titleTXT TR069 CONFIG MODULE Elements
<<VOIP CONFIG FILE>>
 
<TR069 CONFIG MODULE>
ACS Server Type    :1
ACS URL            :0.0.0.0
ACS UserName       :admin
ACS Password       :admin
CPE UserName       :dps
CPE Password       :dps
CPE SerialNumber   :
ProvisioningCode   :
Download Start Time:0
Download End Time  :
TR069 Auto Login   :0
TR069 Tone         :1
Enable TR069       :0
Periodix Interval  :3600
Area Code          :020
TLS Version        :0
<<END OF FILE>>
 

...

Option

Values

Description

ACS Server Type

Integer, 0-1, Defaults to 1

When set to 1, the phone is compatible with Common ACS servers. When set to 0, the phone is compatible with Telecom (CTC) ACS servers. Defaults to 1.

ACS URL

StringSets the address of the ACS server.
ACS UserNameStringSets the username used to authenticate against the ACS server.
ACS PasswordStringSets the password used to authenticate against the ACS server.
CPE UserNameStringSets the CPE username used to authenticate against the ACS server.
CPE PasswordStringSets the CPU password used to authenticate against the ACS server.
CPE SerialNumberStringDisplays the equipment serial number. Not user-configurable.
ProvisioningCodeStringIdentifier of the primary service provider and other provisioning information, which may be used by the server to determine service provider specific customization and provisioning parameters.
Download Start TimeStringSpecifies the time at which to begin the config download
Download End TimeStringSpecifies the time at which to end config downloads
TR069 Auto LoginBoolean, Defaults to 0If enabled, the phone will connect to the ACS server after reboot and launch a certification request. Defaults to 0.

TR069 Tone

Boolean, Defaults to 1If disabled, the phone will not play a prompt tone after a successful TR069 connection. Defaults to 1.
Enable TR069Boolean, Defaults to 0If enabled, the phone will, on boot, send an authentication message to the ACS server. Defaults to 0.
Periodix IntervalInteger, in seconds, Defaults to 3600Sets the CPE packet interval time. Defaults to 3600.
Area CodeInteger, Defaults to 020Sets the ACS server area code. Defaults to 020.
TLS VersionInteger 0-2, Defaults to 0

Sets the TLS protocol version to use when communicating against the ACS server as follows:

TLS 1.0 - 0
TLS 1.1 - 1
TLS 1.2 - 2

Defaults to 0.