Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: With and without internet access are now the same.
{numberedheadings} {toc}
Wiki Markup
Section
Column

Overview

Let's

install

DAHDI!

On

Linux,

we

will

use

the

DAHDI-linux-complete

tarball,

which

contains

both

the

DAHDI

Linux

drivers as well as the DAHDI tools. Again,

drivers, DAHDI tools, and board firmware files. Again, we're

assuming

that

you've

untarred

the

tarball

in

the

the /usr/local/src

directory,

and

that

you'll

replace

X

and

Y

with

the

appropriate

version

numbers.

{note} LibPRI

See What to Download? for more information on downloading the DAHDI tarballs.

Note
titleInstall DAHDI before libpri

libpri 1.4.13

and

later

source

code

depends

on

DAHDI

include

files.

So,

as a change from older versions,

one

must

install

DAHDI

before

installing

libPRI

libpri.

{note} h2. With Internet Access {noformat} [[email protected] src]# cd dahdi-linux-complete-2.X.Y+2.X.Y [[email protected] dahdi-linux-complete-2.X.Y+2.X.Y]# make [[email protected] dahdi-linux-complete-2.X.Y+2.X.Y]# make install [[email protected] dahdi-linux-complete-2.X.Y+2.X.Y]# make config {noformat} h2. Without Internet Access When installing on a system without internet access, there are a few additional steps that are required to build DAHDI. The firmware files for the various VPM modules will need to be downloaded and extracted in the source directory. The file specific links provided below are the current versions as of this writing. Please check the link below for the full list of versions. http://downloads.digium.com/pub/telephony/firmware/releases/ On a system with internet access, download the following files: {noformat} wget http://downloads.digium.com/pub/telephony/firmware/releases/dahdi-fw-hx8-2.06.tar.gz wget http://downloads.digium.com/pub/telephony/firmware/releases/dahdi-fw-oct6114-064-1.05.01.tar.gz wget http://downloads.digium.com/pub/telephony/firmware/releases/dahdi-fw-oct6114-128-1.05.01.tar.gz wget http://downloads.digium.com/pub/telephony/firmware/releases/dahdi-fw-vpmoct032-1.8.0.tar.gz wget http://downloads.digium.com/pub/telephony/firmware/releases/dahdi-fw-tc400m-MR6.12.tar.gz wget http://downloads.digium.com/pub/telephony/firmware/releases/dahdi-fwload-vpmadt032-1.25.0.tar.gz {noformat} Now send these to the Asterisk system and store them in {noformat}/usr/local/src/dahdi-linux-complete-2.X.Y+2.X.Y/linux/drivers/dahdi/firmware/ {noformat} Now we can continue the installation on the Asterisk system using the steps below. {noformat}

Note
titleDon't need DAHDI?

 If you are not integrating with any traditional telephony equipment and you are not planning on using the MeetMe dialplan application, then you do not have to install DAHDI or libpri in order to use Asterisk.

Column
Panel
titleOn This Page

Table of Contents

 

Starting with DAHDI-Linux-complete version 2.8.0+2.8.0, all files necessary to install DAHDI are available in the complete tarball. Therefore, all you need to do to install DAHDI is:

No Format
[[email protected] src]# cd dahdi-linux-complete-2.X.Y+2.X.Y

[[email protected] dahdi-linux-complete-2.X.Y+2.X.Y]# cd linux/drivers/dahdi/firmware

[[email protected]rver firmware]# for tarball in $(ls dahdi-fw-*.tar.gz); do tar -zxf $tarball; done;

[[email protected] firmware]# cd -

[[email protected] dahdi-linux-complete-2.X.Y+2.X.Y]# make

[[email protected] dahdi-linux-complete-2.X.Y+2.X.Y]# make install

[[email protected] dahdi-linux-complete-2.X.Y+2.X.Y]# make config {noformat}

{numberedheadings}