Asterisk Timing Interfaces
In the past, if internal timing were desired for an Asterisk system, then the only source acceptable was from DAHDI. Beginning with Asterisk 1.6.1, a new timing API was introduced which allows for various timing modules to be used.
Asterisk includes the following timing modules:
res_timing_timerfd.so — as of Asterisk 1.6.2
res_timing_kqueue.so — as of Asterisk 11
res_timing_pthread uses the POSIX pthreads library in order to provide timing. Since the code uses a commonly-implemented set of functions,
res_timing_pthread is portable to many types of systems. In fact, this is the only timing source currently usable on a non-Linux system. Due to the fact that a single userspace thread is used to provide timing for all users of the timer,
res_timing_pthread is also the least efficient of the timing sources and has been known to lose its effectiveness in a heavily-loaded environment.
res_timing_dahdi uses timing mechanisms provided by DAHDI. This method of timing was previously the only means by which Asterisk could receive timing. It has the benefit of being efficient, and if a system is already going to use DAHDI hardware, then it makes good sense to use this timing source. If, however, there is no need for DAHDI other than as a timing source, this timing source may seem unattractive. For users who are upgrading from Asterisk 1.4 and are used to the
ztdummy timing interface,
res_timing_dahdi provides the interface to DAHDI via the
dahdi kernel module.
res_timing_timerfd uses a timing mechanism provided directly by the Linux kernel. This timing interface is only available on Linux systems using a kernel version at least 2.6.25 and a glibc version at least 2.8. This interface has the benefit of being very efficient, but at the time this is being written, it is a relatively new feature on Linux, meaning that its availability is not widespread.
res_timing_kqueue uses the Kqueue event notification system introduced with FreeBSD 4.1. It can be used on operating systems that support Kqueue, such as OpenBSD and Mac OS X. Because Kqueue is not available on Linux, this module will not compile or be available there.
What Asterisk does with the Timing Interfaces
By default, Asterisk will build and load all of the timing interfaces. These timing interfaces are "ordered" based on a hard-coded priority number defined in each of the modules. As of the time of this writing, the preferences for the modules is the following:
res_timing_kqueue.so (where available),
The only functionality that requires internal timing is IAX2 trunking. It may also be used when generating audio for playback, such as from a file. Even though internal timing is not a requirement for most Asterisk functionality, it may be advantageous to use it since the alternative is to use timing based on incoming frames of audio. If there are no incoming frames or if the incoming frames of audio are from an unreliable or jittery source, then the corresponding outgoing audio will also be unreliable, or even worse, nonexistent. Using internal timing prevents such unreliability.
Now that you know Asterisk's default preferences for timing modules, you may decide that you have a different preference. Maybe you're on a timerfd-capable system but you would prefer to get your timing from DAHDI since you already are
using DAHDI to drive your hardware.
Alternatively, you may have been directed to this document due to an error you are currently experiencing with Asterisk. If you receive an error message regarding timing not working correctly, then you can use one of the following suggestions to disable a faulty timing module.
- Don't build the timing modules you know you will not use. You can disable the compilation of any of the timing modules using
menuselect. The modules are listed in the "Resource Modules" section. Note that if you have already built Asterisk and have received an error about a timing module not working properly, it is not sufficient to disable it from being built. You will need to remove the module from your modules directory (by default,
/usr/lib/asterisk/modules) to make sure that it does not get loaded again.
- Build, but do not load the timing modules you know you will not use. You can edit
noloaddirectives to disable the loading of specific timing modules by default. Based on the note in the section above, you may realize that your Asterisk setup does not require internal timing at all. If this is the case, you can safely
noloadall timing modules.